Search:

Type: Posts; User: 4.3LXJ

Page 1 of 9 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    13
    Views
    5,021

    Hey Tony, can you swap those sticks around. ...

    Hey Tony, can you swap those sticks around. Seems you could mine, but that was another series. That might cure your leg problem
  2. Replies
    2
    Views
    688

    Has the boots on your axle shafts cracked or...

    Has the boots on your axle shafts cracked or split apart? If so the joint has gotten dry and allowed the balls in the joint to wear a spot that cause the balls in the joint to kind of hit a pot hole...
  3. Replies
    6
    Views
    2,344

    Believe it or not, yes I have seen some. Far too...

    Believe it or not, yes I have seen some. Far too small an axle for a JK
  4. Replies
    13
    Views
    5,021

    So, is it in yet?

    So, is it in yet?
  5. Replies
    6
    Views
    2,344

    Do you have a Dana 44 or Dana 35?

    Do you have a Dana 44 or Dana 35?
  6. Replies
    6
    Views
    2,344

    Tough break on that rear end man. Hope it is...

    Tough break on that rear end man. Hope it is something simple and cheap
  7. Replies
    13
    Views
    5,021

    Hey Tony, just a hint. There is a breather on...

    Hey Tony, just a hint. There is a breather on top. While you have your tcase off and probably have your tranny partially down, hook the breathers together and run it up as high as your electronics...
  8. Replies
    13
    Views
    5,021

    You won't be disappointed. It will take more...

    You won't be disappointed. It will take more than an afternoon to install though. I suggest a tranny jack. It will weigh in at about 140 pounds.
  9. Thread: Power inverter

    by 4.3LXJ
    Replies
    3
    Views
    687

    Things I run are power tools various places and...

    Things I run are power tools various places and an apartment sized refrigerator when camping and wheeling
  10. Thread: Power inverter

    by 4.3LXJ
    Replies
    3
    Views
    687

    Willie, I had the same idea once. I have a 1750...

    Willie, I had the same idea once. I have a 1750 watt inverter and wanted to run a 1hp compressor I had. It wouldn't do it. I found out that the newer inverters are electronic and not the old iron...
  11. Thread: 4.2 vs 4.0

    by 4.3LXJ
    Replies
    12
    Views
    2,231

    That is a good question. I really don't know,...

    That is a good question. I really don't know, but if it was fairly fresh, say less than 100K on it I would ask $1K and expect to get it. I think brand new rebuilds, some of which are somewhat...
  12. Thread: 4.2 vs 4.0

    by 4.3LXJ
    Replies
    12
    Views
    2,231

    You won't have any trouble getting rid of it. ...

    You won't have any trouble getting rid of it. Lots of people want strokers
  13. Thread: 4.2 vs 4.0

    by 4.3LXJ
    Replies
    12
    Views
    2,231

    The heads on fuel injected engines have larger...

    The heads on fuel injected engines have larger ports and many times larger valves than carbureted heads. If you use large runners and ports on carbureted heads you have idle and low end rpm...
  14. Thread: 4.2 vs 4.0

    by 4.3LXJ
    Replies
    12
    Views
    2,231

    OK, so is this a fuel injected or carbureted...

    OK, so is this a fuel injected or carbureted engine? If it is fuel injected, this is a plus. It uses a 4.2 crank and rods and the high output head etc. Highly desirable
  15. Thread: 4.2 vs 4.0

    by 4.3LXJ
    Replies
    12
    Views
    2,231

    That is true. The 4.2 was always billed as the...

    That is true. The 4.2 was always billed as the torque monster, but frankly the AMC 304 had much more usable torque. Sounds like your engine may have been a transplant
  16. Replies
    12
    Views
    2,067

    Welcome to the West. Lots of critters with horns...

    Welcome to the West. Lots of critters with horns out here. I used to live in an area with herds of them on the roads. The wife's car nailed four of them, more than many hunters get with guns. I...
  17. Replies
    3
    Views
    723

    Well, I guess you just need to jack each wheel up...

    Well, I guess you just need to jack each wheel up and rotate the tire to find it.
  18. Replies
    3
    Views
    723

    Yes, I would check the backing plate and make...

    Yes, I would check the backing plate and make sure all the lug nuts are tight. Did you replace the pads too?
  19. Replies
    12
    Views
    2,067

    Have a nice trip. I plan on going next year

    Have a nice trip. I plan on going next year
  20. Thread: Idle RPM Issues

    by 4.3LXJ
    Replies
    3
    Views
    746

    Glad to hear you got is sorted out

    Glad to hear you got is sorted out
  21. Thread: Revving Issues

    by 4.3LXJ
    Replies
    1
    Views
    533

    I am a little out of my league here, but the...

    I am a little out of my league here, but the Cobalt has an electronic (drive by wire) throttle body. They can get messed up fairly easily apparently. But I would hesitate to say go replace the...
  22. Replies
    10
    Views
    2,764

    Hey, you are sharp. That is the one. I liked...

    Hey, you are sharp. That is the one. I liked them so well I bought three of them. Don't need them for the Jeep, it has a 30 gal gas tank. But there are other rigs in the family that do
  23. Replies
    3
    Views
    973

    No problem. Good luck

    No problem. Good luck
  24. Replies
    3
    Views
    973

    It is important. Generally if you don't, the...

    It is important. Generally if you don't, the clutch will chatter when you let it slip a little. It is well worth the investment
  25. Replies
    10
    Views
    2,764

    If I need to carry gas, which is very seldom...

    If I need to carry gas, which is very seldom nowadays unless for someone else, I use a plastic replacement for the GI gas can. Can't remember the brand. But I can find out. Fits in the surplus GI...
Results 1 to 25 of 219
Page 1 of 9 1 2 3 4